Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
The article listed below about Tools You Need to Install a New Bathtub is definitely motivating. Don't miss it.
Mounting a bath tub isn't exactly rocket science, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably tough task. If the old tub is conveniently accessible, the project can relocate speedily; if you need to open a wall surface to remove the old bathtub as well as place the new tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will need an assistant to leave the old tub and also embeded in the brand-new one. Ensure you have certified on your own for the task as well as fit attempting it. As opposed to working with a specialist to take control of a halfway-completed task, it is better to consider using one prior to you begin. Opportunities are you might need an expert plumber to make tube links.
This post will certainly assist you set up a brand-new bath tub in your shower room if you have actually already acquired a brand-new tub and don't require to change the setup of your previous water supply pipelines.
Your tools as well as material list ought to comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome due to the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines are in location between the faucet as well as the sink. Protect the faucet in place with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the level checks out level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and also check all joints and new pipework for leakages and tighten them if necessary. Load the tub and also examine the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub needs to wait up until the tub has actually been utilized a minimum of once as this will settle it right into its final setting.
Getting ready for the Installation
Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and the tiling, resulting in complications with wetness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub? Make a comment down the page. We will be glad to see your thinking about this review. We are looking forward that you visit us again soon. In case you appreciated our post kindly remember to share it. I appreciate reading our article about How to Install a Bathtub.
Book A Service Report this page